examARnow Guides

ACT · Science · Scientific Investigation

Experimental Design

Variables indépendantes, dépendantes et contrôlées ; témoins et conception de nouveaux tests.

ACT (enhanced, 2025–)Science (optional)Poids: ≈20–30 %
S'entraîner : Experimental Design129 questions originales pour cette compétence, corrigées immédiatement.

Ce qui est évalué

Variables, témoins, conditions constantes et conception d'un test.

L'essentiel

Méthode pas à pas

Pièges fréquents

Exemple corrigé

Does catalase produce the O₂? Un essai avec de l'eau à la place de la catalase.

Exemples de questions

Essayez de répondre avant d'ouvrir le corrigé. Les questions sont dans la langue de l'examen.

Question 1

Difficulté: facile≈ 1 min

Passage VI — Wrapping and cooling (data representation)

Students tested how well different materials slow the cooling of hot water. They filled 5 identical metal cans with 400 mL of water at 80°C. One can was left unwrapped. Each of the other cans was wrapped in a different material: aluminum foil (a single layer), or a 1.0 cm thick layer of cotton, wool, or plastic foam. The cans were placed on a wooden table in a room kept at 21°C, and the water temperature in each can was recorded every 10 minutes for 40 minutes. The results are shown in Figure 1.

Figure 1, line graph of water temperature (°C) versus time (min) for 5 cans, all starting at 80°C. None: 10 min 68, 20 min 60, 30 min 53, 40 min 47. Aluminum foil: 10 min 70, 20 min 62, 30 min 56, 40 min 51. Cotton: 10 min 73, 20 min 66, 30 min 61, 40 min 57. Wool: 10 min 74, 20 min 69, 30 min 64, 40 min 60. Plastic foam: 10 min 76, 20 min 72, 30 min 69, 40 min 66.

The unwrapped can was most likely included in the study in order to:

  1. A. provide a baseline for judging how much each wrapping slowed cooling.
  2. B. measure the temperature of the room during the study.
  3. C. show that metal cans keep water hot longer than glass or plastic containers do.
  4. D. keep the water in the other cans from cooling below 21°C.
Voir la réponse et l'explication

Bonne réponse: A. provide a baseline for judging how much each wrapping slowed cooling.

Explication

The unwrapped can shows how fast the water cools with no insulation. Comparing each wrapped can with it shows how much each material helped, so it serves as the control.

The room temperature was kept at 21°C and was not measured with the can. Only metal cans were used, so containers were not compared. An unwrapped can cannot affect the cooling of the other cans.

Question 2

Difficulté: moyenne≈ 1 min

Passage VII — Solubility of 3 salts (research summary)

The solubility of a substance is the greatest mass of it that can dissolve in a given amount of water at a given temperature. A solution that holds that greatest mass is saturated.

Students measured the solubility of 3 salts (Salts X, Y, and Z) in 100 g of water at 5 temperatures. At each temperature, they added a salt to the water in small portions, stirring for 5 minutes after each addition, until some of the salt remained undissolved. They then filtered the mixture, dried and weighed the undissolved salt, and subtracted that mass from the total mass of salt added. The results are shown in Figure 1.

Figure 1, line graph of solubility (g per 100 g of water) versus temperature (°C). Salt X: 0°C: 14; 20°C: 30; 40°C: 60; 60°C: 104; 80°C: 160. Salt Y: 0°C: 36; 20°C: 36; 40°C: 37; 60°C: 37; 80°C: 38. Salt Z: 0°C: 24; 20°C: 18; 40°C: 13; 60°C: 9; 80°C: 6.

In this study, the dependent variable was the:

  1. A. mass of salt that dissolved in 100 g of water.
  2. B. temperature of the water.
  3. C. mass of water used.
  4. D. time spent stirring after each addition.
Voir la réponse et l'explication

Bonne réponse: A. mass of salt that dissolved in 100 g of water.

Explication

The students measured how much salt dissolved (total added minus undissolved): that is the result that depends on the conditions.

Temperature was the variable they chose (independent). The mass of water (100 g) and the stirring time (5 minutes) were kept the same.

Question 3

Difficulté: difficile≈ 1 min

Passage — Light and algae growth (research summary)

Algae are tiny organisms that grow in water and use light to make food. A student grew cultures of one algae species in flasks of nutrient solution kept at 22°C. Each flask started with 1 million cells per mL, and the density of cells was measured every 2 days for 8 days.

Experiment 1: Flasks were kept under low, medium, or high light. Each flask received 1.0 mg/L of nitrate (see Figure 1).

Experiment 2: Flasks were kept under medium light and given different amounts of nitrate. The cell density on day 8 is shown in Table 1.

Table 1
Nitrate (mg/L)Cell density on day 8 (millions of cells/mL)
0.13.0
0.57.2
1.010.5
2.010.6
Figure 1, line graph of cell density in millions of cells per mL versus time in days. Low light: 0: 1; 2: 1.5; 4: 2.2; 6: 3.1; 8: 4.0. Medium light: 0: 1; 2: 2.5; 4: 5; 6: 8; 8: 10.5. High light: 0: 1; 2: 2.8; 4: 5.5; 6: 7.0; 8: 7.2.

A student thinks that the high-light culture stopped growing because it ran out of nitrate. Which of the following would best test this idea?

  1. A. Repeat Experiment 1 at a higher temperature.
  2. B. Add nitrate to a high-light flask on day 6 and keep measuring its density.
  3. C. Remove the high-light flask from the light on day 6.
  4. D. Count the cells in the medium-light flask on day 10.
Voir la réponse et l'explication

Bonne réponse: B. Add nitrate to a high-light flask on day 6 and keep measuring its density.

Explication

If nitrate was limiting, adding more nitrate on day 6 should restart the growth of the high-light culture, which tests the idea directly. The other options change temperature or light, or look at a different flask, so they do not test a nitrate limit.

Continuer à s'entraîner

S'entraîner : Experimental Design129 questions originales pour cette compétence, corrigées immédiatement.

Autres compétences de Science

Format complet de l'examen ACT · Tous les guides